Every pool filter comes with a spec and model information sticker on its tank. This sticker lists the make and model, the list of sizes for that particular model, and their specs. The model number of your specific unit should be marked. The label should also list a serial number.
How do I know what model Hayward pump I have?
SERIAL NUMBER – Find the model tag on the pump housing that displays the Hayward model and serial number. You can then call Hayward (908-355-7995) to have them identify the pump’s age using just the serial number.
How do you read a Hayward filter serial number?
Reading Goldline Serial Numbers August 2011 – Present
- First Digit = Standard Warranty length. 4 = 4 Year Warranty.
- Second Character = Product Family. A = Aquarite.
- Third & Fourth Digit indicate the year the product was made.
- Fifth – seventh digit = day of year manufactured.
- Digits 8 and on = 123456 = Manufacturing ID.
How do I know what filter I need for my pool pump?
The filter flow rate must be rated at least the same GPM as your pump, or higher. With pool filters, it’s best to err on the larger size so it can handle the power of your pump. A helpful rule of thumb is to choose a filter with at least 1 square foot per 10,000 gallons pool capacity.
How do I know what size pool filter I have?
The equation used in calculating filter sizes is:
- Pool capacity in gallons divided by the desired turnover rate in hours.
- This will give you the minimum flow needed in gal/m (Gallons per minute).
- Divide this number by 60 to get the gal/m.
- Find a pump that meets the gal/m you just calculated.
What is the difference between Type A and Type C pool filters?
The only difference between a type A and Type C is the internal diameter of the filter. The A/C Filter type is a hybrid which has an internal rim with a 1-3/4″ internal diameter which will deform to 2″ if the pump really needs an A filter.
Where do I find my pump model number?
To identify the model of your pump, you need to know the part number. Part numbers, also sometimes referred to as model numbers, can be found on your pump’s tag. A pump tag is a small rectangular plate that displays all the basic information about your pump.
How old is my Hayward pump?
How do I determine the age of a Hayward pool heater from the serial number? The 5th and 6th digits of the serial number of a Hayward heat pump pool heater are the year of manufacture, and the next two are the month.
How long does a pool pump last?
eight to 12 years
On average, pool pumps last eight to 12 years before needing replacement. Over time, it’s normal for pool parts to begin to wear down. In addition, swimming pool technology has come a long way in the last decade.
Where is the model number on Aqua Rite?
For products such as Aqua Rite, the serial number needed for registration can be found inside the door of the control panel.
How long do pool filters last?
Pool Filter Life
Pool filter cartridges can run for about 2,000 hours in a filter pump and should be replaced every 1-2 years. Note that the filter cartridge will not last as long due to sunscreen, deodorants, hair care products, and other chemicals that come into contact with your pool water.
Is a sand filter better than a cartridge filter?
If you are looking for a highly efficient solution with the least amount of bacteria and debris left swimming around in your pool, the cartridge filter is your best solution. The cartridge filter can catch finer debris than a sand filter, being 10-20 microns versus 20-40 microns.
How many gallons per hour should my pool pump?
A 1 horsepower pool pump with 1.5-inch plumbing lines may filter around 60 gallons per minute. In this example, that means you would need to run the pool pump for about 8.5 hours a day (8.5 hours x 60 gallons per minute x 60 minutes = 30,600 gallons).
What do the numbers on a pool filter mean?
Once you turn on your pool pump, that number on your gauge is your new baseline pressure. And after you clean it out for the first time—meaning you backwash your sand or D.E. filter, or rinse down your cartridge filter with cleaner—write down that PSI number, too.
What size pool filter do I need for a 20000 gallon pool?
Typical D.E. Filter sizes are 36 sq ft, 48 sq ft, 60 sq ft, and 72 sq ft (they also make a 100 sq ft Quad D.E. Filter). So you can easily get away with using a 48 sq ft D.E. Filter on a 20,000-gallon pool.
What are the different types of pool filters?
There are three different types of filters that are available for use with inground pools. The three types are sand, diatomaceous earth (DE) and cartridge. Each kind has its pros and cons.
How many times can you reuse pool filters?
Generally most people replace their filter cartridges about every 3-5 years, but don’t use the amount of time that has passed as the only determining factor, monitor the performance of your filter. Your time frame may be longer or shorter depending on the demand placed on the cartridge.
How often should pool filters be cleaned?
A pool needs a clean filter and it needs to be cleaned periodically-usually once a month in swim season and perhaps less frequently in the offseason. If your pool’s filter is oversized by design, these filters need cleaning 3-4 times per year by a pool professional.
What size is a type B pool filter?
Dia Type B Pool Replacement Filter Cartridge (10-Pack) 10 x 29005E – The Home Depot.
What is pump model?
Pump model of TRACE defines the interaction of system fluid with a centrifugal pump. Pressure gradient across the pump is calculated as a function of fluid flow rate and fluid properties using pump–curve correlations.
What is a pump serial number?
The serial number is the “fingerprint” of a pump – it defines the size of the motor, the diameter of the impellers and the materials of which it is constructed.